Fire Fighter
Don't let your house
go up in Flames!
Get it Right the First time!

House Fire

Wiring Done Right - Residential Wiring - The Right Way

Residential Wiring -  The Right Way!

Contact us | Creator Info | Legal | Site Map

Ez Forums

Got Questions? Get Answers!
Ask the Experts on EZ-FORUMS

Electrical Wiring and Safety

Trouble Shooting

Trouble Shooting

Range not Working or Only Partially

Printer Friendly Version of Article

WHILE EXTREME CARE HAS BEEN IMPLEMENTED IN THE PREPARATION OF THIS SELF-HELP DOCUMENT, THE AUTHOR AND/OR PROVIDERS OF THIS DOCUMENT ASSUMES NO RESPONSIBILITY FOR ERRORS OR OMISSIONS, NOR IS ANY LIABILITY ASSUMED FROM THE USE OF THE INFORMATION, CONTAINED IN THIS DOCUMENT, BY THE AUTHOR and / OR PROVIDER.

Read the legal disclaimer page - click the legal link in the menu above

Assumptions...

1. It is an Electrical Cooking Range.

2. It was previously wired correctly and working properly.

This is to trouble shoot a power related issue only, questions about repairing interior components of the range itself should be posted to our appliance expert on our forums...

First check the fuses / breakers on the cooking range itself, and if they are look good...

Pull the range away from the wall.

Range Outlet Wiring

Using a voltage checker / multi meter as indicated in the above diagram insert the probes into where the black and red wires are connected to - the reading should be around 240 volts, if you measure between the black and the white OR the red and white- the reading should be around 120 volts.

If you have no 240 volt reading and only one of the 120 volt readings are present then one of the dual pole breakers are likely tripped - check (they are designed that they both should trip at the same time if working as they should). 

If the breaker is ok and the tests indicate the 240 volt and one of the 120 volt readings is missing, then shut off the breaker pull the outlet out and check that all the connections are tight. Switch on breaker do test again (be careful not to touch anything) and check both the actual outlet slots and the wire connection screws, if the screw tests are all ok and the outlet slots do not then replace the outlet. If they are both faulty then you will have to take voltage tests at the breaker, testing between red and black connection screws at the breaker should be 240  volts, black to neutral bus 120 volts and the same between red to neutral bus. If these reading are done correctly and you do not have a readings on part of the test and the breaker  if on and seated properly then replace the breaker itself.

If  240 is present but no 120 volt, then...

The Neutral (white wire) is not connected possible causes...

1. Loose connection at outlet
2. Faulty Outlet
3. Loose connection at neutral bus in the electrical panel.

If the outlet tests ok then the issue is at the cooking range itself.


By: Donald Kerr

Social Media Links

Help spread our popularity, get the word out.

QUICK MENU 

Home (Wiring Done Right)
2011 NEC New Rule 'Switch Connections'
3 Way Switch
4 Way Switch
Accessory Buildings
Adding Outlet
Aluminium Wiring
Arc Circuit Protection
Backup Generators / Transfer Switches
Basic Switch
Box Fill Calculations
Breaker Circuit Types
Conduit Fill
Convert Pull String to Wall Switch
Definitions
Doorbell System / Wiring
Dryer Outlet
Electrical Box Types
Electrical Dangers
Electrical Safety
Electricity, What is It?
Fan / Light Combo
Generation / Distribution Grid
GFI Outlets
Home Electrical Design
Main Electrical Panel
Multiple Fixture Wiring
Old Home / Wiring
Outlet, Half Switched
Range Outlet
Series Switches
Split Circuit Outlet
Sub Panel
Switch Outlet Types
Testing Equipment
Tools, Basic Tools
Trouble Shooting
Light Flicker
Outlet Not Working
Breaker / Fuse keeps Tripping
Odour from Switch / Outlet
GFI Outlet keeps Tripping
Range not Working or Only Partially
Wire Cable Types
Wire Connections
Wire Routing Basics
Work Shop Wiring
World, Electricity around the

Copyright 2012 +
All Rights Reserved
Donald Kerr / Wiring Done Right
https://www.wiringdoneright.com/